IST-D Microprocessor Based Programmable lsolated Signal Transmitter

The IST-D is user configurable using our software on your PC/notebook . The easy to use software is available free from your supplier or can be downloaded from our web site and should be used in conjunction with the URC-1020 USB cable which incorporates an interface converter necessary for communications.The IST-D transmitter can be configured without any loop or power connected making it easy to configure in the workshop before installation.

Specification
Input	Thermocouple (T/C) : industry standard thermocouple types J, K, T, E, B, R, S, N, C (ITS-90).
	Pt100 : Excitation 180uA. 2 or 3 wire connection (ITS-90 α =0.00385).
	Voltage : -60mVdc to 60mVdc or –10Vdc to 10Vdc.
	Current : 0-24mAdc
Accuracy	Refer to Table 1 Input Signal
A/D Resolution	16 bits
Input Sampling Rate	<200 ms
Power Supply	DC 24V
Output	4~20mA analog output
Output Resolution	0.6 μ A(15 bits)
Output Response Time	<200 ms
Common Mode Rejection Ratio (CMRR)	>80 dB
Electromagnetic Compatibility (EMC)	En 50081-2, En 50082-2
Galvanic Isolation	3.75 KV. between input and output
Operating Temperature	-10 to 50°C
Humidity	0 to 90% RH
Dimension	75mm(W)x87mm(H)x18.5mm(D)

Table 1 Input Signal
Input signal	Maximum Range	Accuracy
Thermocouple J	-50 to 1000°C (-58 to 1832°F)	± 1°C
Thermocouple K	-50 to 1370°C (-58 to 2498°F)	± 1°C
Thermocouple T	-270 to 400°C (-454 to 752°F)	± 1°C
Thermocouple E	-50 to 700°C (-58 to 1292°F)	± 1°C
Thermocouple B	0 to 1750°C (32 to 3182°F)	± 2°C (Note1)
Thermocouple R	-50 to 1750°C (-58 to 3182°F)	± 2°C
Thermocouple S	-50 to 1750°C (-58 to 3182°F)	± 2°C
Thermocouple N	-50 to 1300°C (-58 to 2372°F)	± 2°C
Thermocouple C	-50 to 1800°C (-58 to 3272°F)	± 2°C
Pt100	-200 to 600°C (-328 to 1112°F)	± 0.2°C
mV	-60mV to 60mV	± 0.01mV
Voltage (Note2)	-10 to 10Vdc	± 1mV
Current (Note2)	0 to 24mAdc	± 10μA

Note 1: Accuracy is not guaranteed between 0 and 400°C (0 and 752°F) for type B

Note 2: The internal DIP switch should be set

The standard unit is supplied set for thermocouple/PT100 inputs.
The transmitters are user configurable.
Should you require that the factory set the inputs and ranges the full code must be specified

Loop Power Signal Transmitter

Model	Type	Input					Output	Isolated
Model	Type	T/C	PT100	mV	mA	V	Output	Isolated
IST-H	Head Mount	V	V	V	X	X	4-20mA	V
IST-D	DIN Rail	V	V	V	V	V	4-20mA	V
IST-P	Head Mount	0-60KΩ					4-20mA	V
NST	Head Mount	V	V	V	X	X	4-20mA	X

Dual Channel Isolated Signal Converter

Model	Type	Input					Output 1	Output 2	Math Function	Independent Input(*Note)
Model	Type	T/C	PT100	mV	mA	V	Output 1	Output 2	Math Function	Independent Input(*Note)
ISC-D	DIN Rail	V	V	V	V	V	0-24mA/0-10V	0-24mA/0-10V	V	X
ISC-C	DIN Rail	V	V	V	V	V	0-24mA/0-10V	RS485	V	X
ISD-D	DIN Rail	V	V	V	V	V	0-24mA/0-10V	0-24mA/0-10V	X	V
ISD-C	DIN Rail	V	V	V	V	V	0-24mA/0-10V	RS485	X	V
ISA-D	DIN Rail	X	X	V	V	V	0-24mA/0-10V	0-24mA/0-10V	X	V
ISA-C	DIN Rail	X	X	V	V	V	0-24mA/0-10V	RS485	X	V

*Note:

ISD/ISA: Different input type can be set to each channel
ISC: Both channels must be set to same input type

Related Products